thesiliconhorizon
03-11-2007, 06:57 AM
heres the new techFX mini prop controller.
www.thesiliconhorizon.com
its smaller than its big brother the techFX 1.0b....
this one is 3x3 inches and has all screw terminals....
http://www.thesiliconhorizon.com/images/mini_overview.jpg
-48 Mhz 12 MIPS with 32k on MCU and 256K 1 Mhz I2C eeprom
-full speed USB with free bootloader for uploading your own code
17 IO as follows:
------------------------------
-6 high current outputs allow the use of dual voltage (12 or 24 volt accessories)
-10 IO configurable as follows:
-upto 4 A2D 10 bit at 100Ksps
-upto 2 PWM or servo
-all can be TTL in or out (4 have pullup / pulldown resistor selectable)
-I2C terminals for adding accessory modules such as devantechs line of addons (they make an addon that will control a 20 amp motor!!! and 5-50v.. also servo controllers, GPS, compasses, sonar etc.. all on the I2C bus
-switching voltage regulator does 1 amp on the 5 volt line and 1 amp on the external voltage line for 2 amps total on this board! the regulator doesnt get hot like regulat linear regulators!!! less than 1 watt heat dissipation.
-use less wall adapters as you can use 2 voltages on this board... 5 volt line and the wall adapter voltage. (upto 30 volts)
NO CODE WRITING with techFX mini tools, setup your board config in seconds
http://www.thesiliconhorizon.com/images/miniconfig.jpg
then go create your control sequence and send it to the controller.
http://www.thesiliconhorizon.com/images/miniseq.jpg
you can trigger off an input, do loops, execute once, act on analog inputs, issue i2c commands for expander modules. you cant go wrong with this controller!!!
or u can write your own code using our framework source code. It uses simple MCC18 C compiler which is a high level language.
if you blow it up, we do free controller repair for life! great tech support.
come visit us :)
www.thesiliconhorizon.com
www.thesiliconhorizon.com
its smaller than its big brother the techFX 1.0b....
this one is 3x3 inches and has all screw terminals....
http://www.thesiliconhorizon.com/images/mini_overview.jpg
-48 Mhz 12 MIPS with 32k on MCU and 256K 1 Mhz I2C eeprom
-full speed USB with free bootloader for uploading your own code
17 IO as follows:
------------------------------
-6 high current outputs allow the use of dual voltage (12 or 24 volt accessories)
-10 IO configurable as follows:
-upto 4 A2D 10 bit at 100Ksps
-upto 2 PWM or servo
-all can be TTL in or out (4 have pullup / pulldown resistor selectable)
-I2C terminals for adding accessory modules such as devantechs line of addons (they make an addon that will control a 20 amp motor!!! and 5-50v.. also servo controllers, GPS, compasses, sonar etc.. all on the I2C bus
-switching voltage regulator does 1 amp on the 5 volt line and 1 amp on the external voltage line for 2 amps total on this board! the regulator doesnt get hot like regulat linear regulators!!! less than 1 watt heat dissipation.
-use less wall adapters as you can use 2 voltages on this board... 5 volt line and the wall adapter voltage. (upto 30 volts)
NO CODE WRITING with techFX mini tools, setup your board config in seconds
http://www.thesiliconhorizon.com/images/miniconfig.jpg
then go create your control sequence and send it to the controller.
http://www.thesiliconhorizon.com/images/miniseq.jpg
you can trigger off an input, do loops, execute once, act on analog inputs, issue i2c commands for expander modules. you cant go wrong with this controller!!!
or u can write your own code using our framework source code. It uses simple MCC18 C compiler which is a high level language.
if you blow it up, we do free controller repair for life! great tech support.
come visit us :)
www.thesiliconhorizon.com