animatronic problems. help

[dshaunt]

Hi,
Last year my one animatronic (I do a home haunt) was not going up everytime. The motion sensor, solenoid, and all other eletronics activated just fine everytime, but the actual prop just didnt have enough "kick" to get up.

I was told a way to fix this would be by hooking up a blaster tank. I dont know what these are or how to hook them up but the idea was that this small tank would fill up with enough air to give it that kick it needed.

Any help on this would be appreciated.

Thanks,
Drew

[Allen H]

It sounds like the real issue is your compressor is not powerful enough, or the pressure is to low going to the piston. The "blaster" tank they are referring to is just a small perhaps 5 gallon tank hooked up in line between the piston and the compressor, your compressor charges the tank and the tanks pressure activates the piston.
I get mine at Harbor freight
http://search.harborfreight.com/cpis...tank&Submit=Go
make sure to have the pressure set right for the prop you are using, do not exceed the max PSI listed. put a regulator between the storage tank and the prop.
There are far better pneumatic guru's on the board than I, and I hope they fill in any blanks I might have left out .
Allen H

[Boo Crew Production]

Drew and Shane,

To me a blaster tank is an air cannon. An air cannon is NOT what you want to use in this situation.

I would recommend a tank (reserve tank) with a the large enough capacity to operate your prop 3 to 5 times. On this tank I would also suggest a 1-way or a check valve to restrict the flow back in the direction of the compressor. this will ensure once that tank is full it will not force air back towards the compressor in the event the system/compressor's pressure drops below the required pressure to operate your prop.

Another recommendation I would offer is to be sure your air lines are large enough to flow the required air to keep your prop activated.

With out knowing every detail in your air supply system I cannot give you a surefire answer to your issue (air compressor size, and CFM of the air compressor, supply lines (from compressor to prop- from valve to cylinder), valve and cylinder type & size, air dryer or not, and oiler or not.

If the above recommendations don't help, get ahold of us and we will help you out.

[backstagemike]

I think what you're asking about is a buffer tank. Not that this wasn't explained already but to put pictures with words, check out this website. Hope it helps and good luck.

http://www.teamdavinci.com/understanding_pneumatics.htm

[Kelly Anderson]

Did the prop your talking about ever work properly for you? If so how old is the props pnuematics? Has an oiler and a filter dryer been added to the air supply lines?

In my haunt, the building we use can get damp. At least the humidity can get quite high and theres not alot of air exchange through out the year except during construction. I have to pay close attention the the pnuematic components and keep things oiled and free of moisture to prevent the cylinders from getting those sticky spots in them.

Maybe one of the pro's here can touch on maintenance for pnuematics.

Kelly Anderson
HauntYourHouse.net

[dshaunt]

Did the prop your talking about ever work properly for you? If so how old is the props pnuematics? Has an oiler and a filter dryer been added to the air supply lines?

In my haunt, the building we use can get damp. At least the humidity can get quite high and theres not alot of air exchange through out the year except during construction. I have to pay close attention the the pnuematic components and keep things oiled and free of moisture to prevent the cylinders from getting those sticky spots in them.

Maybe one of the pro's here can touch on maintenance for pnuematics.

Kelly Anderson
HauntYourHouse.net

Yes, the prop works great most of the time but every twenty times or so it would not go up. I pulled it out yesterday and found that whenever the compressor was getting close to the min. psi set for the prop is when it would stop working and a few min later after the tank filled up it would work fine. It is only a year old. I got it from frightprops. here is the link to it http://www.frightprops.com/FrightPro...ct.asp?ID=0759

[Kelly Anderson]

Definately sounds like a lack of stored air. The air tank on the air compressor is a bit small for as many times as the prop is going off and the compressor cant keep up. You could aquire a bigger air compressor with more air capacity or as mentioned earlier, just another air tank close to your prop.

Kelly Anderson
HauntYourHouse.net